FAQ: How To Determine Correct Length Bicycle Chain?

How do I know if my bike chain is too long?

Do a simple check on your bike by shifting the chain to the big chainring and the biggest cassette cog; then, push on the end of the derailleur cage (pushing forward) to see how much it will move forward. If it moves just a little, then you’re good. If it moves a lot, then you’ve got too much chain.

How do I know if my chain is too short?

You should also see two slight bends at each jockey wheel of the rear derailleur. If the chain is too short, this shift is difficult to make and the derailleur cage is stretched out and almost parallel to the chainstay. If the chain is really short, then you might not even be able to shift into the largest cog.

How do I know what bike chain to buy?

When selecting a chain, the first consideration is the number of rear sprockets. The rear cog sets have been made with 5, 6, 7, 8, 9, 10, 11, or 12 sprockets. As the number of cogs on the rear hub increases, the spacing between cogs tends to be reduced.

You might be interested:  Question: How To Increase Bicycle Chain Tension?

What size chain do most bicycles use?

The chain in use on modern bicycles has a 1⁄2 inch (12.7 mm) pitch, which is the distance from one pin center to another, ANSI standard #40, where the 4 in “#40” indicates the pitch of the chain in eighths of an inch; and is standard 606 (metric) #8, where the 8 indicates the pitch in sixteenths of an inch.

How do I set the size of a chain link?

Chain Link Sizes: How to Measure Chain Link Sizes

  1. Pitch is measured by finding the distance from the center of one pin to the center of the next pin in line.
  2. Determine your side plate height and thickness by measuring both inside and outside the roller chain to ensure that you’re seeing a good average size.

Why does my chain slip when I pedal hard?

Most of the time, a skipping chain is caused by cable stretch. In the first half dozen rides on a new bike your shift cables stretch the most. They can also stretch over time as you ride. Hippley explains, “It takes cable tension to open a derailleur, which shifts your chain between gears.

How do you calculate chain length?

Begin by counting the number of teeth on the largest front sprocket and largest rear. These numbers are often printed right on the sprockets and cogs. Next, measure the distance between the middle of the crank bolt to the rear axle. This is also the chain stay length.

What do you do if you cut your bike chain too short?

Registered. To make the chain the correct length, cut one link off the left-over piece of chain that you’ve cut off, buy a second (preferably rivet type) master link, fit them both to the “short” cut chain, and then fit that to the bike using the master link that came with the chain.

You might be interested:  Readers ask: What Is A 6 Speed Bicycle Chain?

Is wd40 good for bicycle chains?

WD-40 Specialist® Bike Chain Lube is an all-conditions lubricant that protects bicycle chains in dry, wet, or varying conditions. The fast and easy-to-use aerosol spray helps prevent squeaks and extends the life of the chain.

How often should I change my bike chain?

The 2,000-Mile Rule. To avoid this accelerated wear of your cassette and chainrings, a general rule of thumb is to replace your bike’s chain every 2,000 miles. Mind you, this is just a starting point. No two chains will wear at exactly the same rate because no two riders treat their chains the same. 4

Are 6 7 8 speed chains the same?

5, 6, 7 and 8 speed chains Shimano, SRAM and Campagnolo all use the same chain with 8 speeds. Chain for 7 speeds is a bit wider – 7.3 mm, while a 6 speed one is substantially wider – 7.8 mm.

Leave a Reply

Your email address will not be published. Required fields are marked *