- 1 What size chain do most bicycles use?
- 2 Are 7 and 8 speed chains the same?
- 3 Can I use a 10 speed chain on a 8 speed cassette?
- 4 How do I know my chain size?
- 5 How do I know what size chain my bike needs?
- 6 How often should I change my bike chain?
- 7 Are KMC chains better than Shimano?
- 8 Can I replace a 7 speed freewheel with an 8 speed?
- 9 Can I convert my 8 speed bike to 10-speed?
- 10 What is the difference between 10 and 11 speed chain?
- 11 Is a 7 speed bike good enough?
- 12 How do I choose a chain sprocket size?
- 13 What is the difference between.325 and 3/8 chain?
What size chain do most bicycles use?
The chain in use on modern bicycles has a 1⁄2 inch (12.7 mm) pitch, which is the distance from one pin center to another, ANSI standard #40, where the 4 in “#40” indicates the pitch of the chain in eighths of an inch; and is standard 606 (metric) #8, where the 8 indicates the pitch in sixteenths of an inch.
Are 7 and 8 speed chains the same?
Shimano, SRAM and Campagnolo all use the same chain with 8 speeds. Chain for 7 speeds is a bit wider – 7.3 mm, while a 6 speed one is substantially wider – 7.8 mm. That is why the reverse is not the case and a 7 speed chain and especially a 6 speed one will not work as well on an 8 speed system.
Can I use a 10 speed chain on a 8 speed cassette?
A 10 speed chain should work on an 8-speed drivetrain. if you want 10 speeds, you will need a 10 speed-specific chain, cassette, derailleur and shifter (and a new cable while you’re at it).
How do I know my chain size?
To measure the chain size, if you have just the sprocket, use calipers to measure between the teeth. Measure from center to center of where the chain roller would set between the teeth that will give you the pitch. Once you know the pitch you can determine what chain size you would need.
How do I know what size chain my bike needs?
Begin by counting the number of teeth on the largest front sprocket and largest rear. These numbers are often printed right on the sprockets and cogs. Next, measure the distance between the middle of the crank bolt to the rear axle. This is also the chain stay length.
How often should I change my bike chain?
The 2,000-Mile Rule. To avoid this accelerated wear of your cassette and chainrings, a general rule of thumb is to replace your bike’s chain every 2,000 miles. Mind you, this is just a starting point. No two chains will wear at exactly the same rate because no two riders treat their chains the same. 4
Are KMC chains better than Shimano?
The difference between the Shimano chain and the KMC is marginal; your choice will always come to personal preference. Despite the inconvenience of adjusting the chain, the Shimano runs a lot smoother and will provide you with long-lasting use.
Can I replace a 7 speed freewheel with an 8 speed?
You can change to 8 speed, but a normal rear wheel for roadbikes will not fit directly into the frame because it’s 130 mm wide. Depends on the stiffness of the rear frame if it can be pushed together safely to 130 mm.
Can I convert my 8 speed bike to 10-speed?
Answer: No you don’t need a new hub. However, you will probably need to put a small (~1mm) spacer at the back of the cassette, otherwise you won’t be able to tighten the whole cassette down.
What is the difference between 10 and 11 speed chain?
Chains for 11-speed systems are around 5.4mm wide on the outside, vs. around 5.9mm wide for 10-speed ones, so that’s 0.25mm narrower from the center of the cog tooth to the end of the chain pin on each side.
Is a 7 speed bike good enough?
Every rider has his comfort level while riding, So to summarise, 7- speed is good enough on a bike. So a 7- speed bike provides the right number of speed gears with efficiency to ride on difficult terrains. As long as you are comfortable and happy with the 7- speed bike, the 7-speed will be enough for you.
How do I choose a chain sprocket size?
Determine the number of teeth of the small sprocket. The number of teeth for the large sprocket is determined by multiplying the number of teeth for the small sprocket by the speed ratio. More than 15 teeth on the small sprocket is recommended. The number of teeth on the large sprocket should be less than 120.
What is the difference between.325 and 3/8 chain?
The three-eighths chain is a beefier saw and better suited to one that has more horsepower. It has larger teeth and a heavier duty chain, so it requires more horsepower to operate correctly. 325-inch chain for those saws between 40 and 60 cc.