Contents

- 1 What number chain do bicycles use?
- 2 What do the numbers on a bike chain mean?
- 3 How do I know my chain size?
- 4 How often should I change my bike chain?
- 5 How do I know what speed my bike is?
- 6 What is the difference between a 520 and a 530 chain?
- 7 How do I find the master link on my bike chain?
- 8 What is the difference between.325 and 3/8 chain?
- 9 How do I know my roller chain size?
- 10 How do I tell what grade my chain is?
- 11 How often should I lube my bike chain?

## What number chain do bicycles use?

The chain in use on modern bicycles has a 1⁄2 inch (12.7 mm) pitch, which is the distance from one pin center to another, ANSI standard #40, where the 4 in “#40” indicates the pitch of the chain in eighths of an inch; and is standard 606 (metric) #8, where the 8 indicates the pitch in sixteenths of an inch.

## What do the numbers on a bike chain mean?

Bicycle Chains are generally categorized into two types: 1/2 × 1/8 and 1/2 × 3/32. The first number (1/2) is the chain pitch; the latter numbers (1/8 and 3/32, respectively) indicate the inner width in inches. Number 1/2 × 3/32 chain is used with a derailleur.

## How do I know my chain size?

To measure the chain size, if you have just the sprocket, use calipers to measure between the teeth. Measure from center to center of where the chain roller would set between the teeth that will give you the pitch. Once you know the pitch you can determine what chain size you would need.

## How often should I change my bike chain?

The 2,000-Mile Rule. To avoid this accelerated wear of your cassette and chainrings, a general rule of thumb is to replace your bike’s chain every 2,000 miles. Mind you, this is just a starting point. No two chains will wear at exactly the same rate because no two riders treat their chains the same. 4

## How do I know what speed my bike is?

Multiply the front gear number by the rear gear number to get the number of speeds. For example, if you have two front gears and five back gears, you have a 10-speed bike. If you have one front gear and three back gears, you have a 3-speed bike.

## What is the difference between a 520 and a 530 chain?

The difference is width. 530 sprockets are 3/8″ wide, 520 are 1/4″ wide. 530 chains and sprockets are stronger because they’re thicker, but they’re also heavier.

## How do I find the master link on my bike chain?

To find the master link on your chain, mount your bike in a bike work stand. If you don’t have a work stand, flip the bike over so it rests on its handlebars and saddle. Stand on the drivetrain side of your bike so you’re able to look straight down on the chain.

## What is the difference between.325 and 3/8 chain?

The three-eighths chain is a beefier saw and better suited to one that has more horsepower. It has larger teeth and a heavier duty chain, so it requires more horsepower to operate correctly. 325-inch chain for those saws between 40 and 60 cc.

## How do I know my roller chain size?

Roller Chain Identification Most roller chain has the size stamped right into the side plates. You may see something like “40”, “C2080H” or “10B” stamped in, which the industry number that represents the chain size. Old chains will most likely need to be cleaned in order to see the size.

## How do I tell what grade my chain is?

Just look for the “L” and then the number after it. Each number following the “L” corresponds with a grade of chain. On grade 70 this can also show that the chains are DOT approved!

## How often should I lube my bike chain?

Bicycle Tutor recommends cleaning and lubricating your bike’s drive chain at least once every month to maintain optimal performance and protection. The chain and drivetrain are typically the dirtiest parts of your bike, and this dirt is bad news for bike longevity and performance.