Often asked: Where Do I Purchase A Bicycle Chain For A 10 Speed Bike?

How do I know what chain to get for my bike?

When selecting a chain, the first consideration is the number of rear sprockets. The rear cog sets have been made with 5, 6, 7, 8, 9, 10, 11, or 12 sprockets. As the number of cogs on the rear hub increases, the spacing between cogs tends to be reduced.

Will any 10 speed chain work with Shimano?

Any Shimano- or SRAM-compatible 10-speed chain can be used with any other Shimano 10-speed groupsets, and with any SRAM 10-speed groupset, regardless of manufacturer statements that their chains will provide optimal performance with their components.

Can I use a 12 speed chain on a 10 speed bike?

-chains have the same outer dimension, the 12 speed derailleur would have narrower cogs than what required for a 10 speed. -As long as you can set the high/low limits on the derailleur to keep it on the cassette it should be fine.

What size bike chain do I need single speed?

1/8″ chains are used exclusively for single speed setups. In addition to the other answers, I found it helpful to read that the nominal width of a chain (1/8 or 3/32) actually refers to the width of the sprocket.

You might be interested:  Readers ask: How To Remove Bicycle Handlebars Scratches From Auto Finish?

How often should I change my bike chain?

The 2,000-Mile Rule. To avoid this accelerated wear of your cassette and chainrings, a general rule of thumb is to replace your bike’s chain every 2,000 miles. Mind you, this is just a starting point. No two chains will wear at exactly the same rate because no two riders treat their chains the same. 4

How long do bike chains last?

Replacing your chain regularly can prolong the life of your drivetrain. Most mechanics agree that you should replace your chain about every 2,000 to 3,000 miles, depending on your riding style. Many Tour De France riders wear out two or even three chains on their primary bike over the course of the three-week race.

What is the difference between 10 and 11-speed chain?

Chains for 11-speed systems are around 5.4mm wide on the outside, vs. around 5.9mm wide for 10-speed ones, so that’s 0.25mm narrower from the center of the cog tooth to the end of the chain pin on each side.

Are 9 and 10 speed chains compatible?

10-speed chains have the same inner/roller width as 9-speed chains while being narrower. Therefore, a 10-speed chain meets the compatibility requirements because it has enough inner space for a 9-speed sprocket and doesn’t cause rubbing due to its slimmer profile.

Are SRAM chains better than Shimano?

Both Shimano and SRAM can comfortably claim to have improved longevity with their top-tier 12-speed chains versus the equivalent 11-speed options. “Both the X01 and XX1 chains were so far ahead of any other chain from a pure elongation wear measure that I had to re-run the tests. The results were basically identical.

You might be interested:  Question: How To Remove A Bicycle Front End?

How do I know what speed my bike is?

Multiply the front gear number by the rear gear number to get the number of speeds. For example, if you have two front gears and five back gears, you have a 10-speed bike. If you have one front gear and three back gears, you have a 3-speed bike.

Will an 11 speed derailleur work with 10 speed?

the 10 speed and 11 speed derailleurs are interchangeable as far as the shifters go, the difference is that a 10 speed derailleur doesn’t like a cassette cog much bigger than the 36t it was designed for, where the 11 speed derailleurs are designed for 40 and 42t cogs, and seem to be able to handle bigger.

Are KMC chains better than Shimano?

The difference between the Shimano chain and the KMC is marginal; your choice will always come to personal preference. Despite the inconvenience of adjusting the chain, the Shimano runs a lot smoother and will provide you with long-lasting use.

Leave a Reply

Your email address will not be published. Required fields are marked *