Quick Answer: What Part Of The Bicycle Chain Is 1/8 Of An Inch?

What is a 1/8 bike chain?

1/8 ” (0.125″, 3.18 mm) chain is used on most single-speed bicycles, and bicycles with internal gearing. 3/32″ (0.094″, 2.30 mm) chain is used on derailer equipped bicycles that have more than 3 cogs at the rear. Even somewhat narrower chain, typically.

What number is bicycle chain?

The chain in use on modern bicycles has a 1⁄2 inch (12.7 mm) pitch, which is the distance from one pin center to another, ANSI standard # 40, where the 4 in “#40” indicates the pitch of the chain in eighths of an inch; and is standard 606 (metric) #8, where the 8 indicates the pitch in sixteenths of an inch.

How do you measure a bike chain?

Begin by counting the number of teeth on the largest front sprocket and largest rear. These numbers are often printed right on the sprockets and cogs. Next, measure the distance between the middle of the crank bolt to the rear axle. This is also the chain stay length.

You might be interested:  FAQ: How To Remove A Mountain Bicycle Tire With V Brakes?

Are 7 and 8 speed chains the same?

Shimano, SRAM and Campagnolo all use the same chain with 8 speeds. Chain for 7 speeds is a bit wider – 7.3 mm, while a 6 speed one is substantially wider – 7.8 mm. That is why the reverse is not the case and a 7 speed chain and especially a 6 speed one will not work as well on an 8 speed system.

What is the difference between 1 8 and 3/32 chain?

Bicycle chain comes in two basic widths: 1/8″ chain is used on most single-speed bicycles, and bicycles with internal gearing. 3/32″ chain is used on derailer equipped bicycles that have more than 3 speeds.

What is the difference between bicycle chains?

Chains can vary in side plate shape, sizing, and height. Differences can cause variations in shifting performance between brands and models. Additionally, chains will vary in the quality of steel used. Better chains that are more durable and longer lasting tend to have harder rivets.

How do I know my chain size?

To measure the chain size, if you have just the sprocket, use calipers to measure between the teeth. Measure from center to center of where the chain roller would set between the teeth that will give you the pitch. Once you know the pitch you can determine what chain size you would need.

Are all bicycle chains the same size?

Are all bicycle chains the same size? No, all bicycle chains are not the same size. Size varies on the bike’s numbers of sprockets, speeds, the distance between the front chainring and rear cogs, and the number of teeth on them.

You might be interested:  Readers ask: How To Change Bicycle Crank Chain On Bike?

How often should I change my bike chain?

The 2,000-Mile Rule. To avoid this accelerated wear of your cassette and chainrings, a general rule of thumb is to replace your bike’s chain every 2,000 miles. Mind you, this is just a starting point. No two chains will wear at exactly the same rate because no two riders treat their chains the same. 4

What size bike chain do I need single speed?

1/8″ chains are used exclusively for single speed setups. In addition to the other answers, I found it helpful to read that the nominal width of a chain (1/8 or 3/32) actually refers to the width of the sprocket.

Is my bike chain too short?

If the chain is too short, this shift is difficult to make and the derailleur cage is stretched out and almost parallel to the chainstay. If the chain is really short, then you might not even be able to shift into the largest cog. Before you remove the chain, make sure it’s on the small chainring and smallest cog.

Will a 9 speed chain fit 8 speed?

9 speed chain on an 8 speed cassette is just fine; it’s the wider 8 speed which won’t fit the sprocket spacing on a 9 speed cassette.

Can I use a 9 speed derailleur on a 8 speed?

8 and 9-speed derailleurs have the same rear shift ratio but only when both models are made either by Shimano or SRAM. In consequence, a 9-speed derailleur can work just fine with an 8-speed cassette produced by the same brand. If the bicycle uses index shifting, the shifter will have to be designed for 8 speeds too.

You might be interested:  FAQ: How To Remove A Bicycle Cassette Older Ten Speed?

Can I replace a 7 speed freewheel with an 8 speed?

You can change to 8 speed, but a normal rear wheel for roadbikes will not fit directly into the frame because it’s 130 mm wide. Depends on the stiffness of the rear frame if it can be pushed together safely to 130 mm.

Leave a Reply

Your email address will not be published. Required fields are marked *