- 1 What does a chain idler do?
- 2 What is the drive chain on a bike?
- 3 What is t Cycle?
- 4 Who invented the chain drive bicycle?
- 5 How do you tension a chain and belt?
- 6 How often should I lube my bike chain?
- 7 How do I know my bike chain size?
- 8 What kind of oil do you use on a bike chain?
- 9 What is the difference between machine cycle and T-State?
- 10 Is 8085 an 8 bit or a 16 bit microprocessor?
- 11 What is machine cycle?
- 12 What are the disadvantages of chain drive?
- 13 What is the difference between bicycle chains?
- 14 What size is standard bicycle chain?
What does a chain idler do?
The teeth keep your chain from wandering and, because the line is so taut, the chain spins the idler without any undue friction or slowing. The other half of the chain, the part that runs below the power, is the return. It’s the bottom and just kinda hangs out. Its job is to return back to the chainring.
What is the drive chain on a bike?
The ‘drivetrain’ of the bike consists of all the bits that you use to push (or pull) the bike along.
What is t Cycle?
T-cycles are LD cycles with a period length other than 24 hours (T = L + D). All schemes are plotted on 24 hours scale where the white area represents lights on and the gray area lights off, respectively.
Who invented the chain drive bicycle?
Leonardo Da Vinci is credited with developing the idea of the chain and cog in the 15th century. However, it took nearly 400 years for the idea to become a practical aspect of bicycle design. For a chain drive to be effective it needs to transmit power efficiently from the rider’s legs to the back wheel.
How do you tension a chain and belt?
To adjust chain tension, loosen the bolts that fasten the motor base to mounting angles on both sides. Tighten take-up bolts until desired chain tension is reached. Do not over-tighten. A good rule of thumb is 1/4″ deflection in the chain between the sprockets.
How often should I lube my bike chain?
Bicycle Tutor recommends cleaning and lubricating your bike’s drive chain at least once every month to maintain optimal performance and protection. The chain and drivetrain are typically the dirtiest parts of your bike, and this dirt is bad news for bike longevity and performance.
How do I know my bike chain size?
Add the multiplied chainstay length, the divided number of teeth for the chainring and rear sprocket, and add 1 (or 2.5 cm). The result is the ideal chain length for your bike. For example, you’d add 32.5, 13, 7 and 1 to get 53.5. The length of the chain should be 53.5 inches or 135.89 cm.
What kind of oil do you use on a bike chain?
Light Oil. A light oil is typically best for your bicycle chain in average to dry riding conditions. Light oils are good at penetrating the bushings of chains to minimize the amount of wear that occurs between the links.
What is the difference between machine cycle and T-State?
The time required by the microprocessor to complete an operation of accessing memory or input/output devices is called machine cycle. One time period of frequency of microprocessor is called t-state. A t-state is measured from the falling edge of one clock pulse to the falling edge of the next clock pulse.
Is 8085 an 8 bit or a 16 bit microprocessor?
Although the 8085 is an 8-bit processor, it has some 16-bit operations.
What is machine cycle?
A machine cycle consists of the steps that a computer’s processor executes whenever it receives a machine language instruction. The cycle consists of three standard steps: fetch, decode and execute. In some cases, store is also incorporated into the cycle.
What are the disadvantages of chain drive?
Disadvantages of chain drives
- They can not be used where slip is the system requirement.
- They require precise alignment compared to belt drives.
- They require frequent lubrication.
- They have less load capacity compared with gear drives.
- Their operation is noisy and can cause vibrations.
What is the difference between bicycle chains?
Chains can vary in side plate shape, sizing, and height. Differences can cause variations in shifting performance between brands and models. Additionally, chains will vary in the quality of steel used. Better chains that are more durable and longer lasting tend to have harder rivets.
What size is standard bicycle chain?
Chains come in 3⁄32 in (2.4 mm), 1⁄8 in (3.2 mm), 5⁄32 in (4.0 mm), or 3⁄16 in (4.8 mm) roller widths, the internal width between the inner plates. 1⁄8 in (3.2 mm) chains are typically used on bikes with a single rear sprocket: those with coaster brakes, hub gears, fixed gears such as track bicycles, or BMX bikes.